CARE  &  USE  INSTRUCTIONS

Insulated Beverage Dispenser and Snack Tote:

• Do not machine wash or immerse tote in water. Use only mild soap (no bleach) and warm water to clean inside and outside.
• Inside compartment is Poly-lined but not considered waterproof. Do not fill with water or loose ice.
• Avoid leaving tote in direct sunlight or in hot vehicle when it has food and/or beverage inside.
• Do not place sharp items in the main compartment, in any of the pockets or inside the flap-style pouches.
• Clean pieces and parts only with warm mild soapy water. Rinse completely. Do not use bleach.
• After cleaning allow to thoroughly Air-Dry before storing! NEVER attempt to dry Beverage Dispenser Tote, dispenser spout bag, valve assembly, or gel-ice block in an oven, microwave, clothes dryer, or use a hair dryer, other heat source, or place near or over an open flame.

Using the 12 oz Can Side of Tote to Dispense Beverage:

• Use compartment divider to set desired size, zip flap closed. Put 12oz cans on their side into compartment.
• Reposition divider if space is needed for more cans. Unzip flap and pull out (at a slight angle) a can of beverage.
• Rezip flap closed to keep cold in and grass, leaves, dust, etc. out.

Using the Spout Bag Side of Tote to Dispense Beverage:

• Each 3-Liter fillable beverage bag with spout can hold up to 4 (750ml) bottles of wine or up to 3-Liters of other non-carbonated, non-hot beverage of your choice. Each beverage dispenser spout bag has a white valve seat molded into the bag and a removable black spout assembly
• Lay bag flat on a table, and firmly place one hand around valve seat while grabbing spout assembly with the other hand. Do not grab just the plastic bag! Grabbing just the plastic bag while pulling the spout assembly out can damage the waterproof seal around the base flange of valve seat.
• Firmly pull spout up/out while holding the valve seat. Spout assembly has three molded rings that make a secure watertight seal inside the valve seat. Use enough (but not too much) force to remove spout assembly.
• Fill bag with up to 3-liters of the wine or other non-carbonated (room temperature or cold) beverage of your choice. Carefully squeeze out excess air from inside the dispenser bag. Do not allow liquid to be pushed out of dispenser bag.
• Grasp valve seat with one hand and firmly press spout assembly back into the valve seat. Only one molded ring will show when spout assembly is seated correctly. If a leak appears, spout assembly needs to be reinstalled.
• Place filled Beverage Dispenser Spout Bag into the Du-Al Insulated Beverage Dispenser and Snack Tote and pull valve assembly out through the specially designed zippered round flap. Remove red protection seal by pulling up on tab to expose the push-button on the spout. Do not remove the red “wings” on spout assembly.
• Dispense beverage by pressing button on top of spout. Use the wings to support spout while thumb presses the button. Enjoy your beverage! When finished, push dispenser spout back into tote and zipper the round flap closed.
• To reuse a dispenser bag, first remove spout assembly and empty any remaining liquid. Use mild dish soap in warm water to clean inside. Rinse inside of bag several times and be sure 100% of all soap is completely rinsed out of bag. Leave spout assembly off and hang bag to fully air-dry. Do not replace spout assembly into bag if inside of bag is not completely dry. Wash outside of spout assembly and flow soapy water through spout to clean. Rinse outside and inside of spout to completely remove all soap. Place spout (round open end down) on a towel and allow to fully air-dry.

Sealed Hard Shell Gel-Ice Pack Block:

• Place in freezer until completely frozen then insert into flap-style pouch. Gel-Ice block can be reused many times!
• Never place Ice Block near sharp objects. Use mild soapy water to clean exterior as necessary. NEVER cut open or pierce outer shell of Ice Block. Never eat or drink the gel. Don’t use if gel is leaking out. Keep out of reach of infants and children.